Type WGT Guyed Tower

The WGT is an all-welded tower that can be designed for any loading scenario. An all-welded tower has the advantage of lower erection costs because each 20-foot section is ready to stack when delivered to the tower site.

The WGT is a triangular tower with face widths from 24 inches to 60 inches on a side. Member sizes are varied during fabrication to meet tower design loading. Legs are constructed of mill certified structural pipe or solid round steel with a minimum yield strength of 50 ksi, while horizontal and diagonal bracing members are of ASTM A-36 solid round steel or structural angle. Tower sections are joined with bolted flange plates

Towers come complete with climbing ladders and a cable-type safety climb system. Towers can have climbing members integrated into one face of the tower or have external ladders constructed per TIA-222-G.

All towers are hot-dip galvanized after fabrication according to ASTM designation A-123. Towers can be factory painted upon request, but with proper lighting, the painting of these towers can be totally eliminated, and maintenance is kept to a minimum.

All fasteners are hot dip galvanized and meet or exceed ASTM A-325 specifications.

Ehresmann Engineering stocks many different mounts for guyed towers. We carry dish mounts, ice shields, beacon mounts, T-frames, and many more mounts.

Type KDGT Guyed Tower

The KDGT is a "knock-down" tower intended for microwave applications or large antenna loads. The X-bracing lacing scheme provides maximum strength, without sacrificing ease of assembly.

While a bolt-together tower requires more assembly time in the field, there are two distinct advantages over a welded tower.

  1. The bolt-together tower can be modified to meet load changes overtime. Legs and bracing members are individually sized to meet required loading at each tower elevation. Should future requirements dictate strengthening of a particular section, tower bracing members can be replaced in the field.
  2. The same holds true for members requiring replacement due to physical damage. Bolt-together tower has the advantage of lower freight charges than do pre-assembled tower sections.

The KDGT is a triangular tower with face widths from 36 inches to 56 inches on a side. Member sizes may be varied to meet tower design loading. Legs are constructed of heavy structural steel formed to a 60 degree angle. All surfaces are exposed for inspection, eliminating the possibility of inside corrosion. The KDGT is composed of 4' bays and is X-braced for maximum rigidity throughout its entire length with solid rods. The bracing can vary in size and be modified easily, depending upon the loads it must carry in any given tower section.

Horizontal members are mounted at 4-foot intervals either inside, outside, or on both sides of the tower faces. Each member is punched with a predetermined number of holes per customer request for waveguide runs.

Towers come complete with climbing ladders and a cable-type safety climb. On towers with a face width of 48 inches or greater, the ladder is mounted internally so that two tower faces form a safety cage around the climber.

All towers are hot-dip galvanized after fabrication according to ASTM designation A-121. Towers can be painted on request, but with proper lighting, the painting of these towers can be totally eliminated, and maintenance is kept to a minimum.

      

 WGT Guyed Tower

  • All welded construction
  • Facilitates rapid erection
  • Rigid construction
  • Face widths of 24", 36", 42", 48", and 60"
  • Triangular
  • Pipe or solid round legs
  • Hot dip galvanized finish per ASTM A123
  • Includes integral climbing ladder and cable-type safety climb system on one face on 24" and 30" towers
  • Face widths of 36", 42", and 48" available with external climbing ladders
  • Meets or exceeds TIA-222-G standards
  • All fasteners meets or exceed ASTM A325 specifications

 

 

KDGT Guyed Tower

  • Bolt-together construction
  • Allows modifications for load changes
  • Reduces freight costs
  • Designed for large loads, or for sites with stringent wind or ice loading
  • Face widths of 36", 42", 48", or 56"
  • Triangular
  • Structural angle (formed) legs
  • X-braced for maximum rigidity
  • Hot dip galvanized finish per ASTM A123
  • Includes climbing ladder and cable-type safety climb system
  • Meets or exceeds TIA-222-G standards
  • All fasteners meets or exceed ASTM A325 specifications